HPE 3PAR Fibre Channel and iSCSI drivers

HPE 3PAR Fibre Channel and iSCSI drivers

The HPE3PARFCDriver and HPE3PARISCSIDriver drivers, which are based on the Block Storage service (Cinder) plug-in architecture, run volume operations by communicating with the HPE 3PAR storage system over HTTP, HTTPS, and SSH connections. The HTTP and HTTPS communications use python-3parclient, which is part of the Python standard library.

For information about how to manage HPE 3PAR storage systems, see the HPE 3PAR user documentation.

System requirements

To use the HPE 3PAR drivers, install the following software and components on the HPE 3PAR storage system:

  • HPE 3PAR Operating System software version 3.1.3 MU1 or higher.
    • Deduplication provisioning requires SSD disks and HPE 3PAR Operating System software version 3.2.1 MU1 or higher.
    • Enabling Flash Cache Policy requires the following:
      • Array must contain SSD disks.
      • HPE 3PAR Operating System software version 3.2.1 MU2 or higher.
      • python-3parclient version 4.2.0 or newer.
      • Array must have the Adaptive Flash Cache license installed.
      • Flash Cache must be enabled on the array with the CLI command createflashcache SIZE, where size must be in 16 GB increments. For example, createflashcache 128g will create 128 GB of Flash Cache for each node pair in the array.
    • The Dynamic Optimization license is required to support any feature that results in a volume changing provisioning type or CPG. This may apply to the volume migrate, retype and manage commands.
    • The Virtual Copy License is required to support any feature that involves volume snapshots. This applies to the volume snapshot-* commands.
    • Enabling Volume Compression requires the following:
      • Array must contain SSD disks.
      • HPE 3PAR Operating System software version 3.3.1 MU1 or higher.
      • Array must have the Compression license installed.
      • HPE 3PAR Storage System with 8k or 20k series
  • HPE 3PAR drivers will now check the licenses installed on the array and disable driver capabilities based on available licenses. This will apply to thin provisioning, QoS support and volume replication.
  • HPE 3PAR Web Services API Server must be enabled and running.
  • One Common Provisioning Group (CPG).
  • Additionally, you must install the python-3parclient version 4.2.0 or newer from the Python standard library on the system with the enabled Block Storage service volume drivers.

Supported operations

  • Create, delete, attach, and detach volumes.
  • Create, list, and delete volume snapshots.
  • Create a volume from a snapshot.
  • Copy an image to a volume.
  • Copy a volume to an image.
  • Clone a volume.
  • Extend a volume.
  • Migrate a volume with back-end assistance.
  • Retype a volume.
  • Manage and unmanage a volume.
  • Manage and unmanage a snapshot.
  • Replicate host volumes.
  • Fail-over host volumes.
  • Fail-back host volumes.
  • Retype a replicated volume.
  • Create, delete, update, snapshot, and clone generic volume groups.
  • Create and delete generic volume group snapshots.
  • Create a generic volume group from a group snapshot or another group.
  • Volume Compression.
  • Group Replication with More Granularity (Tiramisu).
  • Volume Revert to Snapshot.
  • Additional Backend Capabilities.

Volume type support for both HPE 3PAR drivers includes the ability to set the following capabilities in the OpenStack Block Storage API cinder.api.contrib.types_extra_specs volume type extra specs extension module:

  • hpe3par:snap_cpg
  • hpe3par:provisioning
  • hpe3par:persona
  • hpe3par:vvs
  • hpe3par:flash_cache
  • hpe3par:compression

To work with the default filter scheduler, the key values are case sensitive and scoped with hpe3par:. For information about how to set the key-value pairs and associate them with a volume type, run the following command:

$ openstack help volume type

Note

Volumes that are cloned only support the extra specs keys cpg, snap_cpg, provisioning and vvs. The others are ignored. In addition the comments section of the cloned volume in the HPE 3PAR StoreServ storage array is not populated.

If volume types are not used or a particular key is not set for a volume type, the following defaults are used:

  • hpe3par:cpg - Defaults to the hpe3par_cpg setting in the cinder.conf file.
  • hpe3par:snap_cpg - Defaults to the hpe3par_snap setting in the cinder.conf file. If hpe3par_snap is not set, it defaults to the hpe3par_cpg setting.
  • hpe3par:provisioning - Defaults to thin provisioning, the valid values are thin, full, and dedup.
  • hpe3par:persona - Defaults to the 2 - Generic-ALUA persona. The valid values are:
    • 1 - Generic
    • 2 - Generic-ALUA
    • 3 - Generic-legacy
    • 4 - HPUX-legacy
    • 5 - AIX-legacy
    • 6 - EGENERA
    • 7 - ONTAP-legacy
    • 8 - VMware
    • 9 - OpenVMS
    • 10 - HPUX
    • 11 - WindowsServer
  • hpe3par:flash_cache - Defaults to false, the valid values are true and false.

QoS support for both HPE 3PAR drivers includes the ability to set the following capabilities in the OpenStack Block Storage API cinder.api.contrib.qos_specs_manage qos specs extension module:

  • minBWS
  • maxBWS
  • minIOPS
  • maxIOPS
  • latency
  • priority

The qos keys above no longer require to be scoped but must be created and associated to a volume type. For information about how to set the key-value pairs and associate them with a volume type, run the following commands:

$ openstack help volume qos

The following keys require that the HPE 3PAR StoreServ storage array has a Priority Optimization license installed.

hpe3par:vvs
The virtual volume set name that has been predefined by the Administrator with quality of service (QoS) rules associated to it. If you specify extra_specs hpe3par:vvs, the qos_specs minIOPS, maxIOPS, minBWS, and maxBWS settings are ignored.
minBWS
The QoS I/O issue bandwidth minimum goal in MBs. If not set, the I/O issue bandwidth rate has no minimum goal.
maxBWS
The QoS I/O issue bandwidth rate limit in MBs. If not set, the I/O issue bandwidth rate has no limit.
minIOPS
The QoS I/O issue count minimum goal. If not set, the I/O issue count has no minimum goal.
maxIOPS
The QoS I/O issue count rate limit. If not set, the I/O issue count rate has no limit.
latency
The latency goal in milliseconds.
priority
The priority of the QoS rule over other rules. If not set, the priority is normal, valid values are low, normal and high.

Note

Since the Icehouse release, minIOPS and maxIOPS must be used together to set I/O limits. Similarly, minBWS and maxBWS must be used together. If only one is set the other will be set to the same value.

The following key requires that the HPE 3PAR StoreServ storage array has an Adaptive Flash Cache license installed.

  • hpe3par:flash_cache - The flash-cache policy, which can be turned on and off by setting the value to true or false.
  • hpe3par:compression - The volume compression, which can be turned on and off by setting the value to true or false.

Other restrictions and considerations for hpe3par:compression:

  • For a compressed volume, minimum volume size needed is 16 GB; otherwise resulting volume will be created successfully but will not be a compressed volume.
  • A full provisioned volume cannot be compressed, if a compression is enabled and provisioning type requested is full, the resulting volume defaults to thinly provisioned compressed volume.

LDAP and AD authentication is now supported in the HPE 3PAR driver.

The 3PAR back end must be properly configured for LDAP and AD authentication prior to configuring the volume driver. For details on setting up LDAP with 3PAR, see the 3PAR user guide.

Once configured, hpe3par_username and hpe3par_password parameters in cinder.conf can be used with LDAP and AD credentials.

Enable the HPE 3PAR Fibre Channel and iSCSI drivers

The HPE3PARFCDriver and HPE3PARISCSIDriver are installed with the OpenStack software.

  1. Install the python-3parclient Python package on the OpenStack Block Storage system.

    $ pip install 'python-3parclient>=4.0,<5.0'
    
  2. Verify that the HPE 3PAR Web Services API server is enabled and running on the HPE 3PAR storage system.

    1. Log onto the HP 3PAR storage system with administrator access.

      $ ssh 3paradm@<HP 3PAR IP Address>
      
    2. View the current state of the Web Services API Server.

      $ showwsapi
      -Service- -State- -HTTP_State- HTTP_Port -HTTPS_State- HTTPS_Port -Version-
      Enabled   Active Enabled       8008        Enabled       8080       1.1
      
    3. If the Web Services API Server is disabled, start it.

      $ startwsapi
      
  3. If the HTTP or HTTPS state is disabled, enable one of them.

    $ setwsapi -http enable
    

    or

    $ setwsapi -https enable
    

    Note

    To stop the Web Services API Server, use the stopwsapi command. For other options run the setwsapi –h command.

  4. If you are not using an existing CPG, create a CPG on the HPE 3PAR storage system to be used as the default location for creating volumes.

  5. Make the following changes in the /etc/cinder/cinder.conf file.

    # 3PAR WS API Server URL
    hpe3par_api_url=https://10.10.0.141:8080/api/v1
    
    # 3PAR username with the 'edit' role
    hpe3par_username=edit3par
    
    # 3PAR password for the user specified in hpe3par_username
    hpe3par_password=3parpass
    
    # 3PAR CPG to use for volume creation
    hpe3par_cpg=OpenStackCPG_RAID5_NL
    
    # IP address of SAN controller for SSH access to the array
    san_ip=10.10.22.241
    
    # Username for SAN controller for SSH access to the array
    san_login=3paradm
    
    # Password for SAN controller for SSH access to the array
    san_password=3parpass
    
    # FIBRE CHANNEL(uncomment the next line to enable the FC driver)
    # volume_driver=cinder.volume.drivers.hpe.hpe_3par_fc.HPE3PARFCDriver
    
    # iSCSI (uncomment the next line to enable the iSCSI driver and
    # hpe3par_iscsi_ips or iscsi_ip_address)
    #volume_driver=cinder.volume.drivers.hpe.hpe_3par_iscsi.HPE3PARISCSIDriver
    
    # iSCSI multiple port configuration
    # hpe3par_iscsi_ips=10.10.220.253:3261,10.10.222.234
    
    # Still available for single port iSCSI configuration
    #iscsi_ip_address=10.10.220.253
    
    
    # Enable HTTP debugging to 3PAR
    hpe3par_debug=False
    
    # Enable CHAP authentication for iSCSI connections.
    hpe3par_iscsi_chap_enabled=false
    
    # The CPG to use for Snapshots for volumes. If empty hpe3par_cpg will be
    # used.
    hpe3par_snap_cpg=OpenStackSNAP_CPG
    
    # Time in hours to retain a snapshot. You can't delete it before this
    # expires.
    hpe3par_snapshot_retention=48
    
    # Time in hours when a snapshot expires and is deleted. This must be
    # larger than retention.
    hpe3par_snapshot_expiration=72
    
    # The ratio of oversubscription when thin provisioned volumes are
    # involved. Default ratio is 20.0, this means that a provisioned
    # capacity can be 20 times of the total physical capacity.
    max_over_subscription_ratio=20.0
    
    # This flag represents the percentage of reserved back-end capacity.
    reserved_percentage=15
    

    Note

    You can enable only one driver on each cinder instance unless you enable multiple back-end support. See the Cinder multiple back-end support instructions to enable this feature.

    Note

    You can configure one or more iSCSI addresses by using the hpe3par_iscsi_ips option. Separate multiple IP addresses with a comma (,). When you configure multiple addresses, the driver selects the iSCSI port with the fewest active volumes at attach time. The 3PAR array does not allow the default port 3260 to be changed, so IP ports need not be specified.

  6. Save the changes to the cinder.conf file and restart the cinder-volume service.

The HPE 3PAR Fibre Channel and iSCSI drivers are now enabled on your OpenStack system. If you experience problems, review the Block Storage service log files for errors.

The following table contains all the configuration options supported by the HPE 3PAR Fibre Channel and iSCSI drivers.

Description of HPE 3PAR Fibre Channel and iSCSI drivers configuration options
Configuration option = Default value Description
[DEFAULT]  
hpe3par_api_url = (String) 3PAR WSAPI Server Url like https://<3par ip>:8080/api/v1
hpe3par_cpg = OpenStack (List) List of the CPG(s) to use for volume creation
hpe3par_cpg_snap = (String) The CPG to use for Snapshots for volumes. If empty the userCPG will be used.
hpe3par_debug = False (Boolean) Enable HTTP debugging to 3PAR
hpe3par_iscsi_chap_enabled = False (Boolean) Enable CHAP authentication for iSCSI connections.
hpe3par_iscsi_ips = (List) List of target iSCSI addresses to use.
hpe3par_password = (String) 3PAR password for the user specified in hpe3par_username
hpe3par_snapshot_expiration = (String) The time in hours when a snapshot expires and is deleted. This must be larger than expiration
hpe3par_snapshot_retention = (String) The time in hours to retain a snapshot. You can’t delete it before this expires.
hpe3par_username = (String) 3PAR username with the ‘edit’ role

Specify NSP for FC Bootable Volume

Given a system connected to HPE 3PAR via FC and multipath setting is NOT used in cinder.conf. When the user tries to create a bootable volume, it fails intermittently with the following error: Fibre Channel volume device not found

This happens when a zone is created using second or later target from 3PAR backend. In this case, HPE 3PAR client code picks up first target to form initiator target map. This can be illustrated with below example.

Sample output of showport command:

$ showport -sortcol 6

N:S:P      Mode State ----Node_WWN---- -Port_WWN/HW_Addr-  Type Protocol Partner FailoverState
0:1:1    target ready 2FF70002AC002DB6   20110002AC002DB6  host       FC       -             -
0:1:2    target ready 2FF70002AC002DB6   20120002AC002DB6  host       FC   1:1:2          none
1:1:1 initiator ready 2FF70002AC002DB6   21110002AC002DB6  rcfc       FC       -             -
1:1:2    target ready 2FF70002AC002DB6   21120002AC002DB6  host       FC   0:1:2          none
2:1:1 initiator ready 2FF70002AC002DB6   22110002AC002DB6  rcfc       FC       -             -
2:1:2    target ready 2FF70002AC002DB6   22120002AC002DB6  host       FC   3:1:2          none
3:1:1    target ready 2FF70002AC002DB6   23110002AC002DB6  host       FC       -             -
3:1:2    target ready 2FF70002AC002DB6   23120002AC002DB6  host       FC   2:1:2          none

Suppose zone is created using targets “2:1:2” and “3:1:2” from above output. Then initiator target map is created using target “0:1:1” only. In such a case, the path is not found, and bootable volume creation fails.

To avoid above mentioned failure, the user can specify the target in 3PAR backend section of cinder.conf as follows:

hpe3par_target_nsp = 3:1:2

Using above mentioned nsp, respective wwn information is fetched. Later initiator target map is created using wwn information and bootable volume is created successfully.

Note: If above mentioned option (nsp) is not specified in cinder.conf, then the original flow is executed i.e first target is picked and bootable volume creation may fail.

>>>>>>> 9e122f116… 3PAR: Add config for NSP single path attach

Creative Commons Attribution 3.0 License

Except where otherwise noted, this document is licensed under Creative Commons Attribution 3.0 License. See all OpenStack Legal Documents.